Owning a decent laptop is beneficial when it comes to productively spending your time on-the-go By for example working gaming or watching your favorite web video creator The only problem is the limited runtime of the laptop’s built-in battery pack which normally get charged up through the included laptop power supply which is fueled by main voltage so to charge slash power the laptop on-the-go I got the idea of creating a portable battery pack which we can charge up fully laptop power supply and later use it to give the laptop and additional runtime of around three hours The process of creating such laptop power bank with all the required voltage levels and safety features was not that simple though So sit back and enjoy my take on creating such a portable laptop battery pack Let’s get started This video is sponsored by JLC PCBs the most popular PCB prototype company in China which produces more than four hundred thousand square meters of PCBs per month So upload your gerber file today to try out their PCB service for only two dollars To start off I had to collect some data The built-in battery pack of my laptop stated a voltage rating of 11.
1V DC and a capacity of 4400mAh So an energy of around 49 Wh The laptop itself states an input voltage of 19.5V with a maximum current draw of 6.15A which also correlates with the ratings of the laptop power supply To test this I plugged in at 5.5 by 2.5 mm DC jack into the laptop and connected it to a lab bench power supply set to 19.5 V DC and sure enough the laptops battery pack started charging and while simultaneously running a benchmark it drew a maximum of close to 5A So 19.5V and a maximum of 6.
15A should be the output characteristic of our laptop power bank. what is also important safety wise is how much the supply voltage fully laptop can vary Now since I did not feel like frying my laptop with overvoltage I rather disconnected the power and started removing a few dozens of screws in order to find out how the DC Jack voltage is connected to the PCB ICs But even after removing the SSD as well as the cooling system I was not able to get to the DC Jack. What I was able to figure out though was that the input voltage is directly connected to this connector whose closest IC were this BQ737 and this TPS51211 The BQ737 is a one to four cell lithium battery charge controller which is obviously used to charge up the three s lithium ion laptop battery pack The IC features a maximum recommended voltage of 24V which gives us some space to play around.
But we should keep in mind that the datasheet also states that a voltage spike beyond the VCC voltage can destroy the IC Now the other I see here known as the TPS51211 is a stepdown controller for notebooks which creates a small voltage for the laptop components What a coincidence. This one even offers an input voltage of up to 28V so even more space to make mistakes with this knowledge we basically learn that 19.5V would be great but does not have to be spot on. Just like the power supply of the laptop does not exactly delivered this value So after reassembling my laptop which was only a bit tedious I tested whether it still work correctly which it did and grabbed my E-bike battery pack from a previous video.
It consists of 13 lithium ion cells in series with two cells in parallel each. but feel free to watch the video about it in order to find out its specifications. How I built it and why I do not use it for my E-bike anymore and thus can repurpose it for those projects The only problem is that thirteen cells in series is not only a bit too big but also comes with quite a high voltage as a solution I desoldered the thick positive and negative battery wires as well as all the balance wires and cut the battery pack at the eight cell series connection This way my new pack got the maximum voltage of 33.
6V a nominal voltage of 28.8V and a minimum voltage of 20V at 2.5V per cell Also the pack can continuously deliver 40A and features a capacity of 5Ah which equals a nominal energy of 144Wh Thus by assuming a conversion efficiency of 70% we should be able to charge up the laptop battery pack up to two times which should give us three more hours of laptop runtime Awesome! The next component for the power bank is this BMS circuit also known as battery management system This circuit adds an over current overcharge and over discharge protection to the battery pack as well as a cell balancing feature which is pretty much mandatory for multi cell battery packs.
So after soldering its included balance wires to the battery pack as well as new power wires and plugging in the connector We gott our predicted output voltage which is mandatory for the next components a powerful buck converter that can output up to 8A After hooking it up and flipping its power switch I adjusted its output voltage to 19.5V and set its current limit to the highest value Through a DC terminal I then connected this output voltage to the laptop which as you can see charging laptops integrated battery just fine Even higher amp values are no problem for the set-up whose heat sink stayed pretty cool during all the tests and most importantly during switching on or off the buck converter it did not create any kind of voltage spikes which would be harmful for the laptop circuitry Next in order to check when the power bank is completely dry I also added a LED voltage tester to the battery pack for which I desoldered its buzzers hooked up a second pair of eight balance wires and connected them all to a male header to easily connect them to the LED power voltage tester.
Now we can see the voltage of each cell and basically disconnect the battery at a cell voltage of 3V Last but not least we need to charge up the battery for which I got myself this powerful boost converter which can output up to 60V and 12A It is important though that it also features a constant current constant voltage mode To use it I firstly connected the output of the laptop power supply to the input of the boost converter and set its output voltage to 33.6V which is eight times the recommended charging voltage or 4.
2V After then turning the constant current potentiometer to its minimum value and hooking up the boost converters output to the battery pack In series to my multimeter in current measuring mode I then adjusted the constant current limit to 2.5A which is two times the recommended charging current of one cell since we got two of them in parallel And as you can see by observing the rising voltage of the battery pack as well as the constant current we are charging the battery properly with the CCCV charging method to later easily check this charging process I also added a voltage / current monitor circuit to the output side of the boost converter.
and after doing a couple of tests this setup seems to work surprisingly well So I created a suitable enclosure for the new battery pack as well as all the complementary components in one 3D design and 3D printed it afterwards. Once the 22 hour printing session was complete I combined the two parts of the enclosure and the lids with a bit of glue and moved on by mounting the switches and DC jacks and since I messed up when measuring the height of the LED voltage tester I had to shorten its PCB a bit before I could glue it into position Afterwards I used hot glue to secure the battery pack inside the enclosure did some cable managements and moved on by wiring all the DC jacks switches and buck converters to one another Of course explaining the wiring through words can be pretty confusing so if you plan to build something similar you can find a wiring scheme for these project as well as pictures and additional information As always in the video description.
Now as soon as I secured the boost and buck converter to the enclosure with M3 screws I added the lid to the project created a connection wire for my laptop and did a final test by charging up the laptop power bank and afterwards using it to power my laptop which both worked flawlessly and with that being said I declare this project a success and I hope that you enjoyed watching this video If so don’t forget to Like Share and Subscribe Stay creative and I will see you next time.
Solar Charger, 25000mAh Battery Solar Power Bank Portable Panel Charger with 36 LEDs and 3 USB Output Ports External Backup Battery for Camping Outdoor for iOS Android (Black)
Solar Charger, 20000mAh Solar Power Bank Portable Charger for Camping External Battery Backup Charger with Dual 2 USB Port/LED Flashlights for All Smartphone, Tablet and Android Cellphone
Solar Charger 20000mAh Portable Outdoor Waterproof Mobile Power Bank, Backpack Camping External Backup Battery Pack Dual USB with 2 LED Flashlight Compass for iPhone Android
Solar Power Bank, Qi Portable Charger 10,000mAh External Battery Pack Type C Input Port Dual Flashlight, Compass (IPX4 Splashproof, Dustproof, Shockproof, Solar Panel Charging, DC5V/2.1A Input)
Solar Charger 26800mAh, ORYTO Qi Wireless Portable Solar Power Bank External Backup Battery, 3 Outputs-5V/3.1A & 2 Inputs Huge Capacity Phone Charger for Smartphones, 18LED Flashlights for Outdoor
Solar Charger, 20000mAh Qi Wireless Power Bank Portable External Backup Battery with 3 Outputs 5V/3A High-Speed and Flashlight for Camping Outdoor Huge Capacity Phone Charger for iOS Android
Solar Charger 20000mAh YOESOID Portable Solar Power Bank with Dual USB Output Waterproof External Battery Pack Compatible Most Smart Phones, Tablets and More